One thing about WebSockets is that you need a lot of resources on the client's side to generate high enough load for the server to actually eat up all the CPU resources.
There are several challenges you have to overcome because the WebSockets protocol is more CPU demanding on the client's side than on the server's side. At the same time you need a lot of RAM to store information about open connections if you have millions of them.
I've been lucky enough to get a couple of new servers for a limited period of time at my disposal for the hardware "burnout" tests. So I decided to use my Lua Application Server — LAppS to do both jobs: test the hardware and perform the LAppS high load tests.
Challenges
First of all WebSockets on the client's side require a pretty fast RNG for traffic masking unless you want to fake it. I wanted the tests to be realistic, so I discarded the idea of faking the RNG by replacing it with a constant. This leaves the only option — a lot of CPU power. As I said, I have two servers: one with dual Intel Gold 6148 CPUs (40 cores in total) 256GB RAM (DDR4-2666) and one with quad Intel Platinum 8180 CPUs (112 cores in total) 384GB RAM (DDR4-2666). I'll be referring to them as Server A and Server B hereafter.
The second challenge — there are no libraries or test suites for WebSockets that are fast enough. Which is why I was forced to develop a WebSockets client module for LAppS (cws).
The tests setup
Both servers have dual port 10GbE cards. Port 1 of each card is aggregated to a bonding interface and these ports on either cards are connected to each other in RR mode. Port 2 of each card is aggregated to a bonding interface in an Active-Backup mode, connected over an Ethernet switch. Each hardware server was running the RHEL 7.6. I had to install gcc-8.3 from the sources to have a modern compiler instead of the default gcc-4.8.5. Not the best setup for the performance tests, yet beggars can't be choosers.
CPUs on Server A (2xGold 6148) have higher frequency than on Server B (4xPlatinum 8180). At the same time Server B has more cores, so I decided to run an echo server on Server A and the echo clients on Server B.
I wanted to see how LAppS behaves under high load with millions of connections and what maximum amount of echo requests per second it can serve. These are actually two different sets of tests because with the connections amount growth the server and clients are doing an increasingly complex job.
Before this I have made all the tests on my home PC which I use for development. The results of these tests will be used for comparison. My home PC has an Intel Core i7-7700 CPU 3.6GHz (4.0GHz Turbo) with 4 cores and 32GB of DDR4-2400 RAM. This PC runs Gentoo with 4.14.72 kernel.
- Home PC
/sys/devices/system/cpu/vulnerabilities/l1tf:Mitigation: PTE Inversion; VMX: conditional cache flushes, SMT vulnerable /sys/devices/system/cpu/vulnerabilities/meltdown:Mitigation: PTI /sys/devices/system/cpu/vulnerabilities/spec_store_bypass:Mitigation: Speculative Store Bypass disabled via prctl and seccomp /sys/devices/system/cpu/vulnerabilities/spectre_v1:Mitigation: __user pointer sanitization /sys/devices/system/cpu/vulnerabilities/spectre_v2:Vulnerable: Minimal generic ASM retpoline, IBPB, IBRS_FW - Servers A and B
/sys/kernel/debug/x86/ibpb_enabled : 1 /sys/kernel/debug/x86/pti_enabled : 1 /sys/kernel/debug/x86/ssbd_enabled : 1 /sys/kernel/debug/x86/ibrs_enabled : 1 /sys/kernel/debug/x86/retp_enabled : 3
I'll make an extra note with the results of the tests of Servers A and B whether these patches are enabled or not.
On my Home PC patch level is never changed.
Installing LAppS 0.8.1
LAppS depends on the luajit-2.0.5 or higher, the libcrypto++8.2 and the wolfSSL-3.15.7 libraries and they have to be installed from sources in RHEL 7.6 and likely in any other linux distribution.
The prefix for installation is /usr/local. Here is the pretty much self-explanatory Dockerfile part for wolfSSL installation
ADD https://github.com/wolfSSL/wolfssl/archive/v3.15.7-stable.tar.gz ${WORKSPACE}
RUN tar xzvf v3.15.7-stable.tar.gz
WORKDIR ${WORKSPACE}/wolfssl-3.15.7-stable
RUN ./autogen.sh
RUN ./configure CFLAGS="-pipe -O2 -march=native -mtune=native -fomit-frame-pointer -fstack-check -fstack-protector-strong -mfpmath=sse -msse2avx -mavx2 -ftree-vectorize -funroll-loops -DTFM_TIMING_RESISTANT -DECC_TIMING_RESISTANT -DWC_RSA_BLINDING" --prefix=/usr/local --enable-tls13 --enable-openssh --enable-aesni --enable-intelasm --enable-keygen --enable-certgen --enable-certreq --enable-curve25519 --enable-ed25519 --enable-intelasm --enable-harden
RUN make -j40 all
RUN make install
And here is the part for the libcrypto++ installation
ADD https://github.com/weidai11/cryptopp/archive/CRYPTOPP_8_2_0.tar.gz ${WORKSPACE}
RUN rm -rf ${WORKSPACE}/cryptopp-CRYPTOPP_8_2_0
RUN tar xzvf ${WORKSPACE}/CRYPTOPP_8_2_0.tar.gz
WORKDIR ${WORKSPACE}/cryptopp-CRYPTOPP_8_2_0
RUN make CFLAGS="-pipe -O2 -march=native -mtune=native -fPIC -fomit-frame-pointer -fstack-check -fstack-protector-strong -mfpmath=sse -msse2avx -mavx2 -ftree-vectorize -funroll-loops" CXXFLAGS="-pipe -O2 -march=native -mtune=native -fPIC -fomit-frame-pointer -fstack-check -fstack-protector-strong -mfpmath=sse -msse2avx -mavx2 -ftree-vectorize -funroll-loops" -j40 libcryptopp.a libcryptopp.so
RUN make install
And the luajit
ADD http://luajit.org/download/LuaJIT-2.0.5.tar.gz ${WORKSPACE}
WORKDIR ${WORKSPACE}
RUN tar xzvf LuaJIT-2.0.5.tar.gz
WORKDIR ${WORKSPACE}/LuaJIT-2.0.5
RUN env CFLAGS="-pipe -Wall -pthread -O2 -fPIC -march=native -mtune=native -mfpmath=sse -msse2avx -mavx2 -ftree-vectorize -funroll-loops -fstack-check -fstack-protector-strong -fno-omit-frame-pointer" make -j40 all
RUN make installOne optional dependency of the LAppS, which may be ignored, is the new library from Microsoft mimalloc. This library makes significant performance improvement (about 1%) but requires cmake-3.4 or higher. Given the limited amount of time for the tests, I decided to sacrifice mentioned performance improvement.
On my home PC, I'll not disable mimalloc during the tests.
Lets checkout LAppS from the repository:
WORKDIR ${WORKSPACE}
RUN rm -rf ITCLib ITCFramework lar utils LAppS
RUN git clone https://github.com/ITpC/ITCLib.git
RUN git clone https://github.com/ITpC/utils.git
RUN git clone https://github.com/ITpC/ITCFramework.git
RUN git clone https://github.com/ITpC/LAppS.git
RUN git clone https://github.com/ITpC/lar.git
WORKDIR ${WORKSPACE}/LAppSNow we need to remove "-lmimalloc" from all the Makefiles in nbproject subdirectory, so we can build LAppS (assuming our current directory is ${WORKSPACE}/LAppS)
# find ./nbproject -type f -name "*.mk" -exec sed -i.bak -e 's/-lmimalloc//g' {} \;
# find ./nbproject -type f -name "*.bak" -exec rm {} \;And now we can build LAppS. LAppS provides several build configurations, which may or may not exclude some features on the server side:
- with SSL support and with statistics gathering support
- with SSL and without statistics gathering (though minimal statistics gathering will continue as it is used for dynamic LAppS tuning in runtime)
- without SSL and without statistic gathering.
Before next step make sure you are the owner of the /opt/lapps directory (or run make installs with sudo)
Let's make two kinds of binaries with SSL support and statistics gathering and without (assuming we are within ${WORKSPACE}/LAppS directory):
# make clean
# make CONF=Release.AVX2 install
# make CONF=Release.AVX2.NO_STATS.NO_TLS installThe resulting binaries are:
- dist/Release.AVX2/GNU-Linux/lapps.avx2
- dist/Release.AVX2.NO_STATS.NO_TLS/GNU-Linux/lapps.avx2.nostats.notls
They will be installed into /opt/lapps/bin.
Please note that the WebSockets client module for Lua is always built with SSL support. Whether it is enabled or not depends on the URI you are using for connection (ws:// or wss://) in runtime.
Test 1. Top performance on home PC. Configuration for baseline.
I've already established that I get best performance when I configure four benchmark service instances with 100 connections each. In the same time I need only three IOWorkers and four echo service instances to achieve best performance. Remember? I have only 4 cores here.
The purpose of this test is just to establish a baseline for further comparison. Nothing exciting here really.
Bellow are the steps required to configure LAppS for the tests.
Self signed certificates
#!/bin/bash
openssl genrsa -out example.org.key 2048
openssl req -new -key example.org.key -out example.org.csr
openssl genrsa -out ca.key 2048
openssl req -new -x509 -key ca.key -out ca.crt
openssl x509 -req -in example.org.csr -CA ca.crt -CAkey ca.key -CAcreateserial -out example.org.crt
cat example.org.crt ca.crt > example.org.bundle.crtRunning this script from within the /opt/lapps/conf/ssl directory will create all required files. Here is the script's output and what I've typed in:
# certgen.sh
Generating RSA private key, 2048 bit long modulus
.................................................................................................................................................................+++++
.....................................+++++
e is 65537 (0x010001)
You are about to be asked to enter information that will be incorporated
into your certificate request.
What you are about to enter is what is called a Distinguished Name or a DN.
There are quite a few fields but you can leave some blank
For some fields there will be a default value,
If you enter '.', the field will be left blank.
-----
Country Name (2 letter code) [AU]:KZ
State or Province Name (full name) [Some-State]:none
Locality Name (eg, city) []:Almaty
Organization Name (eg, company) [Internet Widgits Pty Ltd]:NOORG.DO.NOT.FORGET.TO.REMOVE.FROM.BROWSER
Organizational Unit Name (eg, section) []:
Common Name (e.g. server FQDN or YOUR name) []:
Email Address []:
Please enter the following 'extra' attributes
to be sent with your certificate request
A challenge password []:
An optional company name []:
Generating RSA private key, 2048 bit long modulus
...+++++
............................................................................+++++
e is 65537 (0x010001)
You are about to be asked to enter information that will be incorporated
into your certificate request.
What you are about to enter is what is called a Distinguished Name or a DN.
There are quite a few fields but you can leave some blank
For some fields there will be a default value,
If you enter '.', the field will be left blank.
-----
Country Name (2 letter code) [AU]:KZ
State or Province Name (full name) [Some-State]:none
Locality Name (eg, city) []:Almaty
Organization Name (eg, company) [Internet Widgits Pty Ltd]:none
Organizational Unit Name (eg, section) []:
Common Name (e.g. server FQDN or YOUR name) []:*.example.org
Email Address []:
Signature ok
subject=C = KZ, ST = none, L = Almaty, O = NOORG.DO.NOT.FORGET.TO.REMOVE.FROM.BROWSER
Getting CA Private KeyLAppS configuration
Here is the WebSockets configuration file which is set for TLS 1.3, includes the above generated certificates and configured with 3 IOWorkers (see detailed description of variables in the LAppS wiki).
{
"listeners" : 2,
"connection_weight": 1.0,
"ip" : "0.0.0.0",
"port" : 5083,
"lapps_config_auto_save" : true ,
"workers" : {
"workers": 3,
"max_connections" : 40000,
"auto_fragment" : false,
"max_poll_events" : 256,
"max_poll_wait_ms" : 10,
"max_inbounds_skip" : 50,
"input_buffer_size" : 2048
},
"acl" : {
"policy" : "allow",
"exclude" : []
},
"tls":true,
"tls_server_version" : 4,
"tls_client_version" : 4,
"tls_certificates":{
"ca":"/opt/lapps/conf/ssl/ca.crt",
"cert": "/opt/lapps/conf/ssl/example.org.bundle.crt",
"key": "/opt/lapps/conf/ssl/example.org.key"
}
}Configuring services: the echo server and the echo client (benchmark), each with four instances.
{
"directories": {
"app_conf_dir": "etc",
"applications": "apps",
"deploy": "deploy",
"tmp": "tmp",
"workdir": "workdir"
},
"services": {
"echo": {
"auto_start": true,
"instances": 4,
"internal": false,
"max_inbound_message_size": 16777216,
"protocol": "raw",
"request_target": "/echo",
"acl" : {
"policy" : "allow",
"exclude" : []
}
},
"benchmark": {
"auto_start": true,
"instances" : 4,
"internal": true,
"preload": [ "nap", "cws", "time" ],
"depends" : [ "echo" ]
}
}
}The echo service is pretty trivial:
echo = {}
echo.__index = echo;
echo.onStart=function()
print("echo::onStart");
end
echo.onDisconnect=function()
end
echo.onShutdown=function()
print("echo::onShutdown()");
end
echo.onMessage=function(handler,opcode, message)
local result, errmsg=ws:send(handler,opcode,message);
if(not result)
then
print("echo::OnMessage(): "..errmsg);
end
return result;
end
return echoThe benchmark service creates as many as benchmark.max_connections to benchmark.target and then just runs until you stop the LAppS. There is no pause in the connections' establishment or echo requests bombardment. The cws module API resembles the Web API for WebSockets. Once all benchmark.max_connections are established the benchmark prints the amount of Sockets connected. Once the connection is established the benchmark sends a benchmark.message to the server. After the server replies the anonymous onmessage method of the cws object is invoked, which just sends the same message back to the server.
benchmark={}
benchmark.__index=benchmark
benchmark.init=function()
end
benchmark.messages_counter=0;
benchmark.start_time=time.now();
benchmark.max_connections=100;
benchmark.target="wss://127.0.0.1:5083/echo";
benchmark.message="XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX";
benchmark.meter=function()
benchmark.messages_counter=benchmark.messages_counter+1;
local slice=time.now() - benchmark.start_time;
if( slice >= 1000)
then
print(benchmark.messages_counter.." messages received per "..slice.."ms")
benchmark.messages_counter=0;
benchmark.start_time=time.now();
end
end
benchmark.run=function()
local n=nap:new();
local counter=1;
n:sleep(1);
local array={};
local start=time.now();
while(#array < benchmark.max_connections) and (not must_stop())
do
local sock, err_msg=cws:new(benchmark.target,
{
onopen=function(handler)
local result, errstr=cws:send(handler,benchmark.message,2);
if(not result)
then
print("Error on websocket send at handler "..handler..": "..errstr);
end
end,
onmessage=function(handler,message,opcode)
benchmark.meter();
cws:send(handler,message,opcode);
end,
onerror=function(handler, message)
print("Client WebSocket connection is failed for socketfd "..handler..". Error: "..message);
end,
onclose=function(handler)
print("Connection is closed for socketfd "..handler);
end
});
if(sock ~= nil)
then
table.insert(array,sock);
else
print(err_msg);
err_msg=nil;
collectgarbage("collect");
end
-- poll events once per 10 outgoing connections
-- this will improve the connection establishment speed
if counter == 10
then
cws:eventLoop();
counter=1
else
counter = counter + 1;
end
end
print("Sockets connected: "..#array);
benchmark.start_time=time.now();
while not must_stop()
do
cws:eventLoop();
end
for i=1,#array
do
array[i]:close();
cws:eventLoop();
end
end
return benchmark;Services installation
Now we need to place the service scripts into /opt/lapps/apps//.lua:
- /opt/lapps/apps/benchmark/benchmark.lua
- /opt/lapps/apps/echo/echo.lua
We are ready to run our benchmark now. Just run: rm -f lapps.log; /opt/lapps/bin/lapps.avx2 > log from within the LAppS directory and wait for 5 mins, then press Ctrl-C once, to stop the LAppS (it will not stop immediately, it will shutdown the connections first), or twice (this will interrupt the shutdown sequence).
Ok, we've got a text file with something like this inside:
echo::onStart
echo::onStart
echo::onStart
echo::onStart
running
1 messages received per 3196ms
1 messages received per 3299ms
1 messages received per 3299ms
1 messages received per 3305ms
Sockets connected: 100
Sockets connected: 100
Sockets connected: 100
Sockets connected: 100
134597 messages received per 1000ms
139774 messages received per 1000ms
138521 messages received per 1000ms
139404 messages received per 1000ms
140162 messages received per 1000ms
139337 messages received per 1000ms
140088 messages received per 1000ms
139946 messages received per 1000ms
141204 messages received per 1000ms
137988 messages received per 1000ms
141805 messages received per 1000ms
134733 messages received per 1000ms
...
Let's clean this log file like this:
echo -e ':%s/ms/^V^M/g\n:%g/^$/d\nGdd1G4/Sockets\n4\ndggZZ' | vi $i'^V^M' is visible representation of the following key hits: Ctrl-V Ctrl-V Ctrl-V Ctrl-M, so it will be pretty useless to just copy paste this bash line. Short explanation:
- we have to replace 'ms' symbols with end of line, because we do not need them, they will mess the calculations later on and 4 benchmarks working in parallel may print out their results in one line.
- we need to remove all empty lines afterwards
- we remove the last line as well, because we stop the server
- in the log file there will be only fore lines consisting Sockets connected: 100 (it is because we run only four benchmark services). So we skip 4 lines past the last of them, and than removing everything to the top of the file.
- saving the file.
File is saved and you are back in shell now, and the log file is ready for the next step:
# awk -v avg=0 '{rps=($1/$5);avg+=rps;}END{print ((avg*1000)/NR)*4}' logThis awk single-liner calculates amount of the echo responses per ms, and accumulates the result in avg variable. After all the lines in log file are processed it multiplies avg to 1000 to get the total amount of the echo responses per second, dividing to number of lines and multipling to amount of benchmark services. This gives us the average number of echo responses per second for this test run.
On my PC this number (ERps) is: 563854
Let's do the same without SSL support and see the difference:
- change value of tls variable in ws.json to false
- change benchmark.target in benchmark.lua from wss:// to ws://
- run
rm -f lapps.log; /opt/lapps/bin/lapps.avx2.nostats.notls > logfrom within LAppS directory, and repeat above steps.
I've got: 721236 responses per second
The difference in performance with SSL and without SSL is about 22%. Let's keep these numbers in mind for future reference.
With the same setup on Server A, I've got: 421905 ERpS with SSL and 443145 ERpS without SSL. The patches for Specter and Meltdown were disabled.
On the Server B I've got 270996 ERpS with SSL and 318522 ERpS without SSL with the patches enabled. 385726 and 372126 without and with SSL. The patches for Specter and Meltdown were disabled as well.
The results are worse with the same setup because the CPUs on these servers have lesser frequency.
Please beware that the clients are very dependent on the data availability in /dev/urandom. It may take a while until the clients actually start running, if you already ran it once. So just wait for them to start working, then they are pretty fast at what they do. Just monitor with top if the LAppS instances actually doing any job at all. If /dev/urandom is exhausted then the LAppS will not eat up your CPUs until there is some data available.
Preparing for big tests
First of all we need to make some changes in kernel parameters and do not forget the ulimit for nr of open files. I used almost the same setup like in this article.
Create a file with following content
:
sysctl -w fs.file-max=14000000
sysctl -w fs.nr_open=14000000
ulimit -n 14000000
sysctl -w net.ipv4.tcp_mem="100000000 100000000 100000000"
sysctl -w net.core.somaxconn=20000
sysctl -w net.ipv4.tcp_max_syn_backlog=20000
sysctl -w net.ipv4.ip_local_port_range="1025 65535"Then use source ./filename on both servers to change the kernel parameters and the ulimit.
This time my purpose is to create several millions clients on one server and connect them to the second.
Server A will serve as the WebSockets echo service server side.
Server B will serve as the WebSockets echo service client side.
There is a limitation in LAppS imposed by LuaJIT. You can use only 2GB of RAM per LuaJIT VM. That is the limit of RAM you can use within single LAppS instance for all the services, as the services are the threads linked against one libluajit instance. If any of your services which is running under the single LAppS instance exceeds this limit then all the services will be out of memory.
I found out that per single LAppS instance you can't establish more then 2 464 000 client WebSockets with the message size of 64 bytes. The message size may slightly change this limit, because LAppS passes the message to cws service by allocating the space for this message within the LuaJIT.
This implies that I have to start several LAppS instances with the same configuration on Server B to establish more then 2.4 millions of WebSockets. The Server A (the echo server) does not uses as much memory on LuaJIT side, so the one instance of the LAppS will take care of 12.3 million of WebSockets without any problem.
Let's prepare two different configs for the servers A and B.
{
"listeners" : 224,
"connection_weight": 1.0,
"ip" : "0.0.0.0",
"port" : 5084,
"lapps_config_auto_save" : true ,
"workers" : {
"workers": 40,
"max_connections" : 2000000,
"auto_fragment" : false,
"max_poll_events" : 256,
"max_poll_wait_ms" : 10,
"max_inbounds_skip" : 50,
"input_buffer_size" : 2048
},
"acl" : {
"policy" : "allow",
"exclude" : []
},
"tls": true,
"tls_server_version" : 4,
"tls_client_version" : 4,
"tls_certificates":{
"ca":"/opt/lapps/conf/ssl/ca.crt",
"cert": "/opt/lapps/conf/ssl/example.org.bundle.crt",
"key": "/opt/lapps/conf/ssl/example.org.key"
}
}{
"directories": {
"app_conf_dir": "etc",
"applications": "apps",
"deploy": "deploy",
"tmp": "tmp",
"workdir": "workdir"
},
"services": {
"echo": {
"auto_start": true,
"instances": 40,
"internal": false,
"max_inbound_message_size": 16777216,
"protocol": "raw",
"request_target": "/echo",
"acl" : {
"policy" : "allow",
"exclude" : []
}
}
}
}{
"listeners" : 0,
"connection_weight": 1.0,
"ip" : "0.0.0.0",
"port" : 5083,
"lapps_config_auto_save" : true ,
"workers" : {
"workers": 0,
"max_connections" : 0,
"auto_fragment" : false,
"max_poll_events" : 2048,
"max_poll_wait_ms" : 10,
"max_inbounds_skip" : 50,
"input_buffer_size" : 2048
},
"acl" : {
"policy" : "deny",
"exclude" : []
},
"tls": true,
"tls_server_version" : 4,
"tls_client_version" : 4,
"tls_certificates":{
"ca":"/opt/lapps/conf/ssl/ca.crt",
"cert": "/opt/lapps/conf/ssl/example.org.bundle.crt",
"key": "/opt/lapps/conf/ssl/example.org.key"
}
}Server A has two interfaces:
- bond0 — x.x.203.37
- bond1 — x.x.23.10
One is faster another is slower but it does not really matter. The server will be under heavy load anyways.
Lets prepare a template from our /opt/lapps/benchmark/benchmark.lua
benchmark={}
benchmark.__index=benchmark
benchmark.init=function()
end
benchmark.messages_counter=0;
benchmark.start_time=time.now();
benchmark.max_connections=10000;
benchmark.target_port=0;
benchmark.target_prefix="wss://IPADDR:";
benchmark.target_postfix="/echo";
benchmark.message="XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX";
benchmark.meter=function()
benchmark.messages_counter=benchmark.messages_counter+1;
local slice=time.now() - benchmark.start_time;
if( slice >= 1000)
then
print(benchmark.messages_counter.." messages received per "..slice.."ms")
benchmark.messages_counter=0;
benchmark.start_time=time.now();
end
end
benchmark.run=function()
local n=nap:new();
local counter=1;
n:sleep(1);
local array={};
local start=time.now();
while(#array < benchmark.max_connections) and (not must_stop())
do
benchmark.target_port=math.random(5084,5307);
local sock, err_msg=cws:new(benchmark.target_prefix..benchmark.target_port..benchmark.target_postfix,
{
onopen=function(handler)
local result, errstr=cws:send(handler,benchmark.message,2);
if(not result)
then
print("Error on websocket send at handler "..handler..": "..errstr);
end
end,
onmessage=function(handler,message,opcode)
benchmark.meter();
cws:send(handler,message,opcode);
end,
onerror=function(handler, message)
print("Client WebSocket connection is failed for socketfd "..handler..". Error: "..message);
end,
onclose=function(handler)
print("Connection is closed for socketfd "..handler);
end
});
if(sock ~= nil)
then
table.insert(array,sock);
else
print(err_msg);
err_msg=nil;
collectgarbage("collect"); -- force garbage collection on connection failure.
end
-- poll events once per 10 outgoing connections
-- this will improve the connection establishment speed
if counter == 10
then
cws:eventLoop();
counter=1
else
counter = counter + 1;
end
end
print("Sockets connected: "..#array);
benchmark.start_time=time.now();
while not must_stop()
do
cws:eventLoop();
end
for i=1,#array
do
array[i]:close();
cws:eventLoop();
end
end
return benchmark;Let's store Server A IP addresses into files IP1 and IP2 respectively and then:
for i in 1 2
do
mkdir -p /opt/lapps/apps/benchmark${i}
sed -e "s/IPADDR/$(cat IP1)/g" /opt/lapps/apps/benchmark/benchmark.lua > /opt/lapps/apps/benchmark${i}/benchmark${i}.lua
doneNow we modify the /opt/lapps/etc/conf/lapps.json on Server B to use these two benchmark services:
{
"directories": {
"app_conf_dir": "etc",
"applications": "apps",
"deploy": "deploy",
"tmp": "tmp",
"workdir": "workdir"
},
"services": {
"benchmark1": {
"auto_start": true,
"instances" : 112,
"internal": true,
"preload": [ "nap", "cws", "time" ]
},
"benchmark2": {
"auto_start": true,
"instances" : 112,
"internal": true,
"preload": [ "nap", "cws", "time" ]
}
}
}Are we ready? No we are not. Because we are intent to generate 2 240 000 outgoing sockets to only two addresses and we need more ports on the server side. It is impossible to create more then 64k connections to the same ip:port pair (actually a little less then 64k).
On the Server A in the file LAppS/include/wsServer.h there is a function void startListeners(). In this function we will replace line 126
LAppSConfig::getInstance()->getWSConfig()["port"],with this:
static_cast<int>(LAppSConfig::getInstance()->getWSConfig()["port"])+i,Rebuild LAppS:
make CONF=Release.AVX2 installRunning the tests for 2 240 000 client WebSockets.
Start the LAppS on Server A, then start the LAppS on Server B and redirect the output to a file like this:
/opt/lapps/bin/lapps.avx2 > logEdit, NB:
if you want to run several LAppS instances, then create separate directory for each instnace (like run1,run2, etc) and run each instance from within these directories. This is required for lapps.log file and of course for resulting standard output, for not to be overlapped/overwritten by concurrent LAppS instances. This may take a while till all the connections are established. Let's monitor the progress.
Do not use netstat to watch established connections, it is pointless while it runs indefinitely after like 150k connections which are established in some seconds. Look at the lapps.log on the Server A, in the directory which you were in when started LAppS. You may use following one-liner to see how the connections are established and how are they distributed among IOWorkers:
date;awk '/ will be added to connection pool of worker/{a[$22]++}END{for(i in a){ print i, a[i]; sum+=a[i]} print sum}' lapps.log | sort -n;dateHere is an idea on how rapidly these connections are established:
375874
Sun Jul 21 20:33:07 +06 2019
650874
Sun Jul 21 20:34:42 +06 2019 2894 connections per second
1001874
Sun Jul 21 20:36:45 +06 2019 2974 connections per second
1182874
Sun Jul 21 20:37:50 +06 2019 2784 connections per second
1843874
Sun Jul 21 20:41:44 +06 2019 2824 connections per second
2207874
Sun Jul 21 20:45:43 +06 2019 3058 connections per second
On the Server B we may check amount of benchmarks finished establishing their connections:
# grep Sockets log | wc -l
224After you see that the number is 224 let the servers work for a while, monitor the CPU and memory usage with top. You might see something like this (Server B at left and Server A at the right side):
Or like this (Server B at left and Server A at the right side):
It is clearly the Server B, where the benchmark client services are running, is under heavy load. The Server A is under heavy load too but not always. Some times it chills while the Server B struggles with amount of tasks to work on. The traffic ciphering on TLS is very CPU intensive.
Let's stop the servers (press Ctrl-C several times) and modify the log as before but with respect to changed amount of benchmark services (224):
echo -e ':%s/ms/^V^M/g\n:%g/^$/d\nGdd1G224/Sockets\n224\ndggZZ' | vi $i
awk -v avg=0 '{rps=($1/$5);avg+=rps;}END{print ((avg*1000)/NR)*224}' logYou might want to delete several last lines as well, to account for print outs from stopping benchmark services. You've already got an idea on how to do this. So I'll post the results for different test scenarios and proceed with problems I've faced.
Results for all the other tests (4.9 million and beyond)
Problems.
Marked in above table with red.
Running more then 224 benchmark instances on the Server B proved to be the bad idea, as the server on client side was incapable of evenly distribute the CPU time among processes/threads. First 224 benchmark instances which have established all their connections took most of the CPU resources and the rest of benchmark instances are lagging behind. Even using renice -20 does not help a lot(448 benchmark instances, 2 LAppS instances):
The Server B (left side) is under very heavy load and the Server A still has free CPU resources.
So I doubled the benchmark.max_connections instead of starting more of the separate LAppS instances.
Still for 12.3 million of WebSockets to run, I have started 5th LAppS instance (tests 5 and 6) without stopping four already running ones. And played the role of CFQ by manually suspending and restarting prioritized processes with kill -STOP/-CONT or/and renice their priorities. You can use following template script for this:
while [ 1 ];
do
kill -STOP <4 fast-processes pids>
sleep 10
kill -CONT <4 fast-processes pids>
sleep 5
doneWelcome to 2019 RHEL 7.6! Honestly, I used the renice command first time since 2009. What is worst, — I used it almost unsuccessfully this time.
I had a problem with scatter-gather engine of the NICs. So I disabled it for some tests, not actually marking this event into the table.
I had partial link disruptions under heavy load and the NIC driver bug, so I had to discard related test results.
End of story
Honestly, the tests went much smoother than I've anticipated.
I'm convinced that I have not managed to load LAppS on Server A to its full potential (without SSL), because I had not enough CPU resources for the client side. Though with TLS 1.3 enabled, the LAppS on the Server A was utilizing almost all available CPU resources.
I'm still convinced that LAppS is most scalable and fastest WebSockets open source server out there and the cws WebSockets client module is the only of it's kind, providing the framework for high load testing.
Please verify the results on your own hardware.
Note of advice: Never use nginx or apache as the load balancer or as a proxy-pass for WebSockets, or you'll end up cutting the performance on order of magnitude. They are not build for WebSockets.